RX-797. Stereo Receiver OWNER S MANUAL MANUAL DE INSTRUCCIONES


Save this PDF as:
 WORD  PNG  TXT  JPG

Tamaño: px
Comenzar la demostración a partir de la página:

Download "RX-797. Stereo Receiver OWNER S MANUAL MANUAL DE INSTRUCCIONES"

Transcripción

1 RL RX-797 Stereo Receiver OWNER S MANUAL MANUAL DE INSTRUCCIONES

2 CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this sound system in a well ventilated, cool, dry, clean place away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 3 cm on the top, cm on the left and right, and cm on the back of this unit. 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use force on switches, knobs and/or cords. When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth. Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. 3 To prevent damage by lightning, keep the power cord and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm. Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons. 5 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. Install this unit near the AC outlet and where the AC power plug can be reached easily. 7 Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is faulty. Before moving this unit, press MASTER ON/OFF to release it outward to the OFF position, and disconnect the AC power plug from the wall outlet. 9 VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are: General model...ac ///3 V, 5/ Hz Asia model...ac /3 V, 5/ Hz \ WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by MASTER ON/OFF, or MAIN ZONE ON/OFF and ZONE ON/OFF. In this state, this unit is designed to consume a very small quantity of power.

3 CONTENTS INTRODUCTION FEATURES... SUPPLIED ACCESSORIES... CONTROLS AND FUNCTIONS... 3 Front panel... 3 Front panel display... 5 Rear panel... Remote control... 7 Zone remote control... 9 Installing batteries in the remote controls... Using the remote controls... PREPARATION CONNECTIONS... Connecting speakers... Connecting audio and video components... Connecting the AM and FM antennas... 3 Connecting the power supply cord... 5 Turning on and off this unit... BASIC OPERATION PLAYING AND RECORDING... 7 Playing a source... 7 Adjusting the tonal quality... 9 Recording a source... Using the sleep timer... Muting the sound output... FM/AM TUNING... 3 Automatic tuning... 3 Manual tuning... Automatic preset tuning... 5 Manual preset tuning... 7 Selecting preset stations... Exchanging preset stations... ADVANCED OPERATION ADVANCED SETUP...9 Changing the ADVANCED SETUP menu parameters... 9 Switching the remote control ID... 3 ZONE...3 Connecting the Zone components... 3 Controlling Zone... 3 REMOTE CONTROL FEATURES...33 Control area Controlling other components... 3 Setting remote control codes ADDITIONAL INFORMATION TROUBLESHOOTING...3 SPECIFICATIONS...39 INTRODUCTION PREPARATION BASIC OPERATION ADVANCED ADDITIONAL OPERATION INFORMATION English

4 FEATURES FEATURES Built-in -channel power amplifier Minimum RMS output power W W ( Ω),.9% THD, Hz to khz Highly dynamic power, low impedance drive capability Sophisticated AM/FM tuner -station random access preset tuning Automatic preset tuning Preset station exchanging capability Radio Data System tuning capability (Europe model only) Other features PURE DIRECT button used to reproduce the purest source sound CD DIRECT AMP button used to reproduce the purest CD sound REC OUT selector independent of input source selection Continuously variable loudness control Sleep timer Remote control capability Zone remote control supplied Zone custom installation facility y indicates a tip for your operation. Some operations can be performed by using either the buttons on the front panel of this unit or those on the remote controls. In case the button names differ between this unit and the remote controls, the names of the buttons on the remote controls are given in parentheses. In case the buttons on the remote control and the Zone remote control have certain functions in common, the illustrations of the buttons on the remote control are used for explanation throughout the manual. This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority. Please check that you received all of the following parts. SUPPLIED ACCESSORIES Remote control Zone remote control Power cable (Two for Asia model) AM loop antenna STANDBY TV AV ZONE CD STANDBY CD MD/TAPE MD/TAPE REC CODE SET A DISC SKIP B u FREQ/TEXT MODE PTY SEEK EON START SLEEP PRESET d TV VOL TV CH MUTE A/B TV MUTE 5 TV INPUT MUTE 3 7 w e f DISPLAY DIR A DIR B REC b s a DISC ID ID CD TAPE p Indoor FM antenna (U.S.A., Canada and General models) Indoor FM antenna (Europe and Australia models) 9 ENT. TITLE MENU BAND ENTER RETURN DISPLAY PRESET/CH Batteries (x) (AA, R, UM-3) Batteries (x) (AAA, R3, UM-)

5 CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS Front panel A B C D MASTER ON OFF MAIN ZONE ON/OFF INPUT PHONES MASTER ON/OFF Press inward to the ON position to turn on the power of this unit. Press again to release it outward to the OFF position to turn off this unit. See page for details. Note A B ZONE ON/OFF ZONE CONTROL Even when this unit is turned off, this unit consumes a small amount of power to preserve the memory. MAIN ZONE ON/OFF Turns on Main Zone of this unit or sets it to the standby mode. See page for details. This switch is operational only when MASTER ON/OFF is pressed inward to the ON position. In the standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control. 3 A/B Turns on or off the speaker set connected to the A and/or B terminals on the rear panel each time the corresponding button is pressed (see page 7). BASS FM/AM EDIT l TUNING h MEMORY MAN'L/AUTO FM MD/TAPE REC OUT SOURCE CD TREBLE BALANCE L R LOUDNESS 5 7 TUNING MODE AUTO/MAN'L FLAT 3dB 3 9 F G H I J K L M N Memory back-up The memory back-up circuit prevents the stored data from being lost. However, the stored data will be lost if the power cord is disconnected from the AC wall outlet for more than one week. Notes PURE DIRECT ZONE ON/OFF Turns on Zone or set it to the standby mode. When Zone is turned on, signals are output at the ZONE OUT jacks. Note This switch is operational only when MASTER ON/OFF is pressed inward to the ON position. 5 ZONE CONTROL Press to control the input source of Zone. Notes CD DIRECT AMP This button is operational only when Zone is turned on. When you press this button, the ZONE indicator flashes in the front panel display for approximately 5 seconds. Select the input source of Zone while the indicator is flashing. You can select the preset station when is selected as the input source of Zone. Remote control sensor Receives infrared signals from the remote control. Note DISPLAY Switch the remote control ID between ID and ID when using multiple YAMAHA receivers or amplifiers (see pages 9, 9 and 3). 7 Front panel display Shows information about the operational status of this unit. -db (General model) E INTRODUCTION English 3

6 CONTROLS AND FUNCTIONS EDIT Exchanges the assignment of two preset stations with each other when is selected as the input source (see page ). 9 FM/AM Switches the reception band between AM and FM when is selected as the input source (see page 3). TUNING l / h Selects the tuning frequency when is selected as the input source (see page 3). A TUNING MODE Switches the tuning mode between automatic (the AUTO indicator turns on as a result) and manual (the AUTO indicator turns off as a result) when is selected as the input source. B MEMORY Stores a station in the system memory (see page 7). Sets this unit to the automatic preset tuning mode (see page 5). C PURE DIRECT and indicator Allows you to listen to a source in the purest possible sound. The indicator above it lights up when this function is turned on. See page 9 for details. D CD DIRECT AMP and indicator Allows you to listen to a CD source in the purest possible sound. The indicator above it lights up and the front panel display turns off when this function is turned on. See page 9 for details. E Increases or decreases the sound output level. Note This does not affect the OUT (REC) level. F INPUT selector Selects the input source you want to listen to or watch. G Selects the preset station group (A to E) when is selected as the input source (see page ). H PHONES jack Outputs audio for private listening with your headphones. Note Press A/B so that the SP A/B indicators turn off before you connect your headphones to the PHONES jack. I REC OUT selector Selects a source for recording to the MD recorder or the tape deck independently of the INPUT selector setting, allowing you to record the selected source while listening to another source (see page ). J BASS Increases or decreases the low frequency response. The position produces a flat response (see page 9). K TREBLE Increases or decreases the high frequency response. The position produces a flat response (see page 9). L BALANCE Adjusts the sound output balance of the left and right speakers to compensate for sound imbalances caused by speaker locations or listening room conditions (see page 9). M LOUDNESS Retains a full tonal range at any volume level to compensate for the human ears loss of sensitivity to high and low-frequency ranges at a low volume level (see page 9). N Preset station number buttons ( to ) Selects the preset station number ( to ) directly when is selected as the input source (see page ).

7 CONTROLS AND FUNCTIONS Front panel display SP MD/TAPE CD A B ZONE ZONE3 MEMORY AUTO TUNED STEREO SLEEP MUTE PTY HOLD EON PS RT PTY CT SP () A/B indicators Light up according to the set of speakers selected. Both indicators light up when both sets of speakers are selected. ZONE indicator Lights up when Zone is turned on. 3 Input source indicators Light up when this unit is in the corresponding mode. MEMORY indicator Flashes for approximately 5 seconds after MEMORY on the front panel is pressed. While the MEMORY indicator is flashing, store the displayed station in the system memory by using and one of the preset station number buttons on the front panel. 5 AUTO indicator Lights up when this unit is in the automatic tuning mode. STEREO indicator Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the AUTO indicator is lit. 9 A 7 SLEEP indicator Lights up when the sleep timer is turned on. MUTE indicator Flashes while the MUTE function is turned on. 9 Multi-information display Shows information when adjusting or changing settings. TUNED indicator Lights up when this unit is tuned into a station. Europe model only A Radio Data System indicators The box-shaped indicator beside the name of each Radio Data System mode lights up when the corresponding Radio Data System mode is selected. PTY HOLD indicator Lights up while searching for stations in the PTY SEEK mode. EON indicator Lights up when the Radio Data System station that offers the EON data service is being received. INTRODUCTION English 5

8 CONTROLS AND FUNCTIONS Rear panel 3 5 (General model) REMOTE AC IN IN GND DTV/ CBL DTV/ CBL OUT AM ANT IN IN IN CONTROL OUT VOLTAGE SELECTOR AC OUTLETS SWITCHED 75Ω UNBAL. FM ANT GND OUT MONITOR OUT OUT IN (PLAY) V 5mA MAX. COUPLER MAIN IN A IMPEDANCE SELECTOR SET BEFORE ON CD ZONE OUT MD/ TAPE OUT (REC) PRE OUT A OR B: ΩMIN. /SPEAKER A OR B: ΩMIN. /SPEAKER AB: ΩMIN. /SPEAKER AB:ΩMIN. /SPEAKER VIDEO ZONE OUT SUB WOOFER B AUDIO AUDIO OUTPUT 7 9 A B C D Antenna terminals Connect FM and AM antennas. See page 3 for connections information. AUDIO/VIDEO jacks Connect audio and video components. See page for connection information. 3 REMOTE jacks These jacks are used to input/output remote control signals. See page 3 for connection information. CONTROL OUT jack This is a control expansion jack. Consult your nearest authorized YAMAHA dealer or service center about this jack. 5 AC IN Use to plug in the supplied power cable. See page 5 for connection information. AC OUTLET(S) (SWITCHED) Use to supply power to your other audio and video components. See page 5 for details. 7 CD jacks Connect a CD player. See page for connection information. jacks and GND terminal Connect a turntable. See page for connection information. 9 ZONE jacks Connect a Zone component. See page 3 for connection information. SUBWOOFER OUTPUT jack Connect a subwoofer with built-in amplifier. A COUPLER jacks Connect an external unit. See page 5 for connection information. B terminals Connect speakers. See page for connection information. C IMPEDANCE SELECTOR switch Switches the impedance setting. See page 5 for details. Asia and General models only D VOLTAGE SELECTOR See page 5 for details.

9 CONTROLS AND FUNCTIONS Remote control This section describes the function of each button on the remote control used to control this unit or other components made by YAMAHA or other manufacturers. The functions of the buttons used to control your other audio and video components are the same as those of the corresponding buttons on those components. Refer to those components instruction manuals for details. To operate other components using this remote control, see REMOTE CONTROL FEATURES on page Infrared signal transmitter Sends infrared signals. TV STANDBY CD MD/TAPE REC DISC SKIP FREQ/TEXT MODE TV VOL TV MUTE 5 9 TITLE BAND RETURN AV PTY SEEK TV CH TV INPUT ENTER PRESET/CH CODE SET MUTE SLEEP MENU Input selector buttons Select the desired input source and change the control area (see page 33). EON START 3 7 ENT. (Europe model) DISPLAY A B 7 9 A B C D 3 Radio Data System control buttons Controls the Radio Data System features. Note The Radio Data System features (FREQ/TEXT, EON, PTY SEEK MODE and PTY SEEK START) are only applicable to the Europe model and are operational only when is selected as the input source. Numeric buttons ( to ) Select the preset station number ( to ) when is selected as the input source. 5 BAND Switches to the previously used reception band (FM or AM) when is selected as the input source. Note The frequency of the previously received station is automatically recalled. j / i Selects the preset station group (A to E) when is selected as the input source (see page ). PRESET/CH u / d Selects the preset station number ( to ) when is selected as the input source (see page ). 7 STANDBY Sets this unit to the standby mode. Notes This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position. In the standby mode, this unit consumes a small amount of power to receive infrared signals from the remote control. This button does not set Zone to the standby mode. Turns on this unit. Notes This button is operational only when MASTER ON/OFF on the front panel is pressed inward to the ON position. This button does not turn on Zone. INTRODUCTION English 7

10 CONTROLS AND FUNCTIONS 9 Changes the control area (see page 33). A/B Turns on or off the set of speakers connected to the A and/or B terminals on the rear panel of this unit when the corresponding button is pressed each time. A CODE SET Use to set up remote control codes (see page 35). B SLEEP Sets the sleep timer. C / Increases or decreases the sound output level. Notes This does not affect the OUT (REC) level. When you press / to control the sound output level of this unit, on the front panel rotates. D MUTE Mutes the sound output. Press again to restore the sound output to the previous volume level (see page ). Note The sound output to Zone is not muted.

11 CONTROLS AND FUNCTIONS Zone remote control This section describes the function of each button on the Zone remote control used to control Zone. You can also use the Zone remote control to control YAMAHA CD players and YAMAHA cassette tape deck. 3 5 CD ZONE MD/TAPE u PRESET d DIR A A/B w e f p DIR B b s a ID STANDBY Infrared signal transmitter Sends infrared signals. Input selector buttons Select the desired input source of Zone. ID MUTE DISPLAY REC DISC CD (Europe model) TAPE 7 9 A 3 PRESET u / d Selects the preset station number ( to ) when is selected as the input source. Selects the preset station group (A to E) when is selected as the input source. 5 CD/TAPE control buttons Controls YAMAHA CD players or YAMAHA cassette tape deck. ID/ID switch Switches the remote control ID between ID and ID (see page 3). 7 Turns on Zone. STANDBY Sets Zone to the standby mode. 9 / Increases or decreases the sound output level of Zone. Note This does not affect the OUT (REC) level. MUTE Mutes the sound output to Zone. Press again to restore the sound output to the previous volume level. A CD/TAPE switch Switches the function of the control buttons numbered 5 between controlling YAMAHA CD players and controlling YAMAHA cassette tape deck. INTRODUCTION English 9

12 MASTER ON OFF MAIN ZONE ON/OFF A INPUT B ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h MD/TAPE TV REC OUT SOURCE CD STANDBY CD MD/TAPE REC DISC SKIP FREQ/TEXT MODE TV VOL TV MUTE 5 9 TITLE BAND RETURN AV PTY SEEK TV CH TV INPUT ENTER PRESET/CH CODE SET EON START SLEEP 3 7 MUTE ENT. MENU DISPLAY A B TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUNING MODE AUTO/MAN'L 3dB 3 9 PURE DIRECT CD DIRECT AMP CONTROLS AND FUNCTIONS Installing batteries in the remote controls Notes on batteries Change all of the batteries if the operation range of the remote controls decreases. Use AA, R, UM-3 batteries for the remote control and AAA, R3, UM- batteries for the Zone remote control. Make sure that the polarities are correct. See the illustration inside the battery compartment of each remote control. Remove the batteries if the remote controls are not used for an extended period of time. Do not use old batteries together with new ones. Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color. We strongly recommend using alkaline batteries. If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries. Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations. Remote control Zone remote control 3 3 Open the battery compartment cover. 3 Close the cover back. Insert the supplied batteries in each remote control according to the polarity markings ( and ) on the inside of the battery compartment. Using the remote controls The remote controls transmit a directional infrared beam. Be sure to aim the remote controls directly at the remote control sensor on the front panel of this unit or on the infrared signal receiver in Zone during operation. 3 3 Approximately m (9.7 ft) Handling the remote controls The area between the remote controls and this unit (or the infrared signal receiver in Zone ) must be clear of large obstacles. Do not spill water or other liquids on the remote controls. Do not drop the remote controls. Do not leave or store the remote controls in the following types of conditions: places of high humidity, such as near a bath places of high temperature, such as near a heater or a stove places of extremely low temperatures dusty places Do not expose the remote control sensor to strong lighting, in particular, an inverter type fluorescent lamp; otherwise, the remote controls may not work properly. If necessary, position this unit away from direct lighting.

13 CONNECTIONS CONNECTIONS Connecting speakers Be sure to connect the left channel (L), right channel (R), (red) and (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. CAUTION Before connecting the speakers, make sure that the power of this unit is turned off. Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or the speakers. Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor. Remove approximately mm (3/ in) of insulation from the end of each speaker cable and twist the exposed wires of the cable together to eliminate the risk of a short-circuit. mm (3/ in) Unscrew the knob. Red: positive () Black: negative () 3 Insert one bare wire into the hole in the side of each terminal. Red: positive () Black: negative () Tighten the knob to secure the wire. Notes on the speaker cord A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped, grooved or ridged cable to the (red) terminals on this unit and your speaker. Connect the plain cable to the (black) terminals on this unit and your speaker. Connecting the banana plug (U.S.A., Canada, Australia and General models only) First, tighten the knob and then insert the banana plug into the end of the corresponding terminal. Notes Banana plug Red: positive () Black: negative () One or two speaker sets can be connected to this unit. If you use only one speaker set, connect it to either the A or B terminals. Use speakers with the specified impedance shown on the rear panel of this unit. PREPARATION English

14 CONNECTIONS Connecting audio and video components CAUTION Do not connect this unit or other components to the main power until all connections between components are complete. All connections must be correct: L (left) to L, R (right) to R, to and to. Also, refer to the owner s manual for each of your components. Use the RCA type pin plug cables for audio and video components except speakers. y The jacks are designed to connect a turntable with an MM or high-output MC cartridge. If you have a turntable with a lowoutput MC cartridge, use an in-line boosting transformer or an MC-head amplifier when connecting your turntable to the jacks. Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to the GND terminal for some record players. Digital TV, Cable TV player, etc. Video monitor V Video out R L Audio out V Video out R L Audio out V Video out R L Audio out R L Audio in V Video in V Video in GND DTV/ CBL DTV/ CBL AM ANT IN IN CD player Audio out 75Ω UNBAL. FM ANT OUT OUT Turntable L R Audio out R CD GND VIDEO MONITOR OUT ZONE OUT IN (PLAY) MD/ TAPE OUT (REC) ZONE OUT L AUDIO AUDIO GND Audio in R L R L Audio out MD recorder, Tape deck, etc.

15 CONNECTIONS Connecting the AM and FM antennas Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. AM loop antenna (included) Outdoor AM antenna Use a 5 to m of vinylcovered wire extended outdoors from a window. Indoor FM antenna (included) Outdoor FM antenna Notes Ground (GND terminal) For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. 75Ω UNBAL. A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult your nearest authorized YAMAHA dealer or service center about outdoor antennas. If you connect an outdoor FM antenna to this unit, do not connect the indoor FM antenna to this unit. To minimize interference from automobile ignition, locate the antenna as far from heavy traffic as possible. Keep the feeder cable or coaxial cable as short as possible. Do not bundle or roll up excess cable. The antenna should be placed at least meters from reinforced concrete walls or metal structures. GND AM ANT FM ANT GND PREPARATION English 3

16 CONNECTIONS Connecting the AM loop antenna Set up the AM loop antenna. 5 Repeat steps to to insert the AM loop antenna lead wires into the GND terminal. Orient the AM loop antenna for the best reception. Notes Press and hold the tab. The AM loop antenna should be placed away from this unit. A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. It is recommended that you should connect a 5 to m of vinyl-covered wire to the AM ANT terminal and extend it outdoors from a window. Consult your nearest authorized YAMAHA dealer or service center about outdoor antennas. The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. 3 Insert the AM loop antenna lead wires into the AM ANT terminal. Release the tab.

17 CONNECTIONS Connecting the power supply cord Plug the power cable into the AC IN on the rear panel of this unit and then plug the power supply cord into the AC wall outlet after all other connections are complete. COUPLER jacks Removing the jumper pins from the PRE OUT/MAIN IN jacks enables this unit to operate separately as a control amplifier or a power amplifier. These jacks are used to connect a signal-processing system such as a graphic equalizer or a surround-sound processor to this unit. If such an external unit is connected to these jacks, the control of this unit can be used to adjust the overall sound output level. To connect an external unit, first remove the jumper pins from the PRE OUT/MAIN IN jacks and then connect the input jacks of that external unit to the PRE OUT jacks or its output jacks to the MAIN IN jacks. For details, refer to the owner s manual included with the external unit to be connected. Notes VOLTAGE SELECTOR IMPEDANCE SELECTOR SET BEFORE ON A OR B: ΩMIN. /SPEAKER AB: ΩMIN. /SPEAKER VOLTAGE SELECTOR A OR B: ΩMIN. /SPEAKER AB:ΩMIN. /SPEAKER Power cable (General model) IMPEDANCE SELECTOR switch AC OUTLETS SWITCHED When you do not use the COUPLER jacks, never remove the jumper pins from these jacks. If removed, no sound will be output from this unit. When you use this unit with an external unit connected to the COUPLER jacks, make sure that the CD DIRECT AMP button and the PURE DIRECT button on the front panel are turned off. When you use this unit as a power amplifier, connect the output jacks of an external control amplifier, etc. to the MAIN IN jacks of this unit. In this case, the controls of this unit will not function except the PHONES jack and the A/B buttons. Use the controls on the external control amplifier to make volume adjustments, etc. AC IN AC OUTLET(S) AC OUTLET(S) (SWITCHED) Australia model... outlet Other models... outlets Use these outlets to connect the power supply cords from your other components to this unit. The outlets supply power to any connected components whenever the power of this unit is turned on. For information on the maximum power (total power consumption of components), see SPECIFICATIONS on page 39. VOLTAGE SELECTOR (Asia and General models only) VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging the power supply cord into the AC wall outlet. Voltages are as follows: Asia model... AC /3 V, 5/ Hz General model... AC ///3 V, 5/ Hz IMPEDANCE SELECTOR switch Do not slide the IMPEDANCE SELECTOR switch while the power of this unit is turned on, as doing so may damage the unit. Select the switch position (left or right) according to the impedance of the speakers in your system. Switch position Right Left Notes CAUTION Impedance level If you use one set (A or B), the impedance of each speaker must be Ω or higher. If you use two sets (A and B), the impedance of each speaker must be Ω or higher. If you use one set (A or B), the impedance of each speaker must be Ω or higher. If you use two sets (A and B), the impedance of each speaker must be Ω or higher. The Canada model cannot use two separate speaker sets (A and B) simultaneously when the IMPEDANCE SELECTOR switch is slid to the Ω position. If this unit fails to turn on, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If this is the case, slide the switch all the way to either position when the power supply to this unit is completely cut off. PREPARATION English 5

18 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUNING MODE AUTO/MAN'L 3dB 3 9 PURE DIRECT -db CD DIRECT AMP CONNECTIONS Turning on and off this unit When all connections are complete, turn on the power of this unit. Press MASTER ON/OFF on the front panel inward to the ON position to turn on the power of this unit. Main Zone of this unit turns on. MASTER ON OFF You can set Main Zone of this unit to the standby mode by pressing MAIN ZONE ON/OFF on the front panel or STANDBY on the remote control. Press MAIN ZONE ON/OFF on the front panel or on the remote control to turn Main Zone of this unit on again. Press MASTER ON/OFF on the front panel again to release it outward to the OFF position to turn off this unit. y While MASTER ON/OFF on the front panel is pressed inward to the ON position, you can turn on Zone or set it to the standby mode independently (see page 3).

19 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP PLAYING AND RECORDING PLAYING AND RECORDING CAUTION Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS. Playing a source Press A and/or B on the front panel or on the remote control to select speakers A and/or speakers B. A B or A B Front panel Remote control 5 Rotate the INPUT selector on the front panel (or press one of the input selector buttons on the remote control) to select the desired input source. INPUT Front panel TV STANDBY CD MD/TAPE REC DISC SKIP FREQ/TEXT MODE TV VOL AV PTY SEEK TV CH or CODE SET EON START SLEEP A B TV STANDBY CD MD/TAPE AV Remote control Notes Both A and B can be selected. Make sure that the IMPEDANCE SELECTOR switch is correctly set (see page 5). 3 Play the source. Rotate on the front panel (or press / on the remote control) to adjust the sound output level. -db Front panel or Remote control BASIC OPERATION English 7

20 PLAYING AND RECORDING 5 Adjust the tonal quality by using the BASS, TREBLE, BALANCE and LOUDNESS controls or the CD DIRECT AMP and the PURE DIRECT buttons on the front panel. BASS TREBLE BALANCE LOUDNESS FLAT 3dB 3 9 L R 5 7 PURE DIRECT CD DIRECT AMP Press MAIN ZONE ON/OFF on the front panel again (or press STANDBY on the remote control) to finish using this unit and set it to the standby mode. MAIN ZONE ON/OFF or STANDBY Front panel Remote control

21 PLAYING AND RECORDING Adjusting the tonal quality Adjusting the BALANCE control Adjusts the sound output balance of the left and right speakers to compensate for sound imbalance caused by speaker locations or listening room conditions. Using the CD DIRECT AMP button Routes input signals from your CD player directly to the specially built-in amplifier for the CD player. As a result, the input signals bypass the INPUT selector and the BASS, TREBLE, BALANCE and LOUDNESS controls and then sent to the power amplifier, thus eliminating any alterations to the CD signals and creating the purest possible sound. The CD DIRECT AMP indicator lights up and the front panel display turns off after a few seconds. Using the PURE DIRECT button Routes input signals from your audio sources so that the input signals bypass the BASS, TREBLE, BALANCE and LOUDNESS controls, thus eliminating any alterations to the audio signals and creating the purest possible sound. Note BALANCE L R If both the CD DIRECT AMP and the PURE DIRECT buttons are turned on, only the CD DIRECT AMP button will function. Adjusting the BASS and TREBLE controls Adjust the high and low frequency response. BASS Increases or decreases the low frequency response. TREBLE Increases or decreases the high frequency response. BASS CD DIRECT AMP PURE DIRECT TREBLE Adjusting the LOUDNESS control Retains a full tonal range at any volume level, thus compensating for the human ears loss of sensitivity to high and low-frequency ranges at a low volume level. CAUTION If the CD DIRECT AMP or the PURE DIRECT button is turned on with the LOUDNESS control set at a certain level, the input signals bypass the LOUDNESS control, resulting in a sudden increase in the sound output level. To prevent your ears or the speakers from being undesirably damaged, be sure to press the CD DIRECT AMP or the PURE DIRECT button after lowering the sound output level or after checking that the LOUDNESS control is properly set. Rotate the LOUDNESS control on the front panel to the FLAT position. LOUDNESS FLAT 3dB Rotate on the front panel (or press / on the remote control) to set the sound output level to the loudest listening level that you would listen to. -db Front panel Remote control 3 Rotate the LOUDNESS control until the desired volume is obtained. or LOUDNESS FLAT 3dB BASIC OPERATION English 9

22 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP PLAYING AND RECORDING Recording a source Notes The, BASS, TREBLE, BALANCE and LOUDNESS controls and the CD DIRECT AMP and the PURE DIRECT buttons have no effect on the source being recorded. Check the copyright laws in your country to record from records, CDs, radio, etc. Recording copyright-protected material may infringe on copyright laws. Rotate on the front panel (or press / on the remote control) to adjust the sound output level of the selected source to record from. -db or Front panel Remote control 5 Begin recording on the MD recorder, the tape deck or the connected to this unit. 3 Rotate the REC OUT selector on the front panel to select the source you want to record from. MD/TAPE REC OUT SOURCE CD Note If you set the REC OUT selector to a source other than the one that you are watching or listening to, selecting another source with the INPUT selector on the front panel (or the corresponding input selector button on the remote control) while recording is in progress will not affect the recording. y You can monitor the sound and/or picture being recorded by rotating the INPUT selector on the front panel (or pressing MD/ TAPE or on the remote control) to select the MD recorder, the tape deck or the used for recording. To record the current input source that you are watching or listening to, set the REC OUT selector to SOURCE. To record a source other than the one that you are watching or listening to, set the REC OUT selector to the source you want to record. Play the selected source to record from. 3 Rotate the INPUT selector on the front panel to confirm the selected source to record from. INPUT

23 PLAYING AND RECORDING Using the sleep timer Use this feature to automatically set this unit to the standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off any external components connected to the AC OUTLET(S). TV STANDBY CD MD/TAPE REC DISC SKIP FREQ/TEXT MODE TV VOL AV PTY SEEK TV CH CODE SET EON START SLEEP A B 3 Press SLEEP repeatedly so that SLEEP OFF appears in the front panel display. SLEEP After a few seconds, SLEEP OFF disappears from the front panel display, and the SLEEP indicator turns off. y The sleep timer setting can also be canceled by pressing STANDBY on the remote control (or MAIN ZONE ON/OFF or MASTER ON/OFF on the front panel) to set this unit to the standby mode. Notes The sleep timer can only be set with the remote control. The sleep timer automatically turns off Zone. However, the power of Zone components are not turned off. Press one of the input selector buttons on the remote control to select an input source. Start playback on the selected input source. 3 Press SLEEP repeatedly to set the amount of time before this unit is set to the standby mode. Each time you press SLEEP, the front panel display changes as shown below. The SLEEP indicator flashes while switching the amount of time for the sleep timer. STANDBY CD MD/TAPE SLEEP min SLEEP OFF TV AV SLEEP SLEEP 3 min SLEEP 9 min SLEEP min SLEEP BASIC OPERATION English

24 PLAYING AND RECORDING Muting the sound output Press MUTE on the remote control to mute the sound output. The MUTE indicator flashes in the front panel display and MUTE ON appears in the front panel display. MUTE MUTE After a few seconds, MUTE ON disappears from the front panel display. Press MUTE on the remote control again to resume the sound output. The MUTE indicator disappears from the front panel display. MUTE

25 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP FM/AM TUNING There are tuning methods; automatic and manual. Select either method according to your preference and the strength of station signals. Automatic tuning Automatic tuning is effective when station signals are strong and there is no interference. FM/AM TUNING Press TUNING l / h once to begin automatic tuning. Press h to tune into a higher frequency. Press l to tune into a lower frequency. 3 l TUNING h Rotate the INPUT selector (or press on the remote control) to select as the input source. INPUT Front panel Press FM/AM on the front panel to select the reception band (FM or AM). FM or AM appears in the front panel display. 3 Press TUNING MODE on the front panel so that the AUTO indicator lights up in the front panel display. TUNING MODE AUTO/MAN'L FM/AM or Remote control AUTO Lights up Notes When you tune into a station, the frequency of the received station is shown in the front panel display. To search for another station, press TUNING l / h once more. If the tuning search does not stop at the desired station because the station signals are weak, try using the manual tuning method. BASIC OPERATION English 3

26 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT 5 7 TUNING MODE AUTO/MAN'L 3dB 3 9 PURE DIRECT -db CD DIRECT AMP FM/AM TUNING Manual tuning Manual tuning is effective when station signals are weak. 3 Press TUNING l / h to manually tune into the desired station. Hold down the button to continue tuning search. l TUNING h Notes When you tune into a station, the frequency of the received station is shown in the front panel display. If you tune into an FM station, it is automatically received in the monaural mode to increase signal quality. Rotate the INPUT selector (or press on the remote control) to select as the input source. INPUT or Front panel Remote control Press FM/AM on the front panel to select the reception band (FM or AM). FM or AM appears in the front panel display. FM/AM 3 Press TUNING MODE on the front panel so that the AUTO indicator disappears from the front panel display. TUNING MODE AUTO/MAN'L AUTO Disappears

27 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP FM/AM TUNING Automatic preset tuning You can use the automatic preset tuning method to automatically store FM stations. This function enables this unit to automatically tune into FM stations with strong signals and store up to ( stations in each of the 5 groups, A to E) of those received stations in order. You can then easily recall any preset stations by selecting the preset station numbers where they are stored. Notes Any station data stored under a preset station number is cleared when you store a new station under that preset station number. If the number of received stations does not reach (E), automatic preset tuning automatically stops once searching all available stations are tuned into and stored. Only FM stations with sufficient signal strength are stored automatically by automatic preset tuning. If the station you want to store is weak in signal strength, try using the manual preset tuning method. Rotate the INPUT selector (or press on the remote control) to select. INPUT Front panel or 3 Remote control Press FM/AM on the front panel to select FM as the reception band. FM appears in the front panel display. 3 Press and hold MEMORY on the front panel for more than 3 seconds. The preset station group and the MEMORY and AUTO indicators flash in the front panel display. Press TUNING l / h once to begin automatic preset tuning. Press h to tune into higher frequencies. Press l to tune into lower frequencies. When automatic preset tuning is complete, the frequency of the last preset station is shown in the front panel display. Notes FM/AM MEMORY MAN'L/AUTO FM l TUNING h If TUNING l / h is not pressed within approximately 5 seconds while the MEMORY and AUTO indicators are flashing, automatic preset tuning automatically begins from the currently displayed frequency and proceeds toward higher frequencies. Received stations are sequentially programmed to stations in each preset station group. If stations are all programmed in a preset station group, another stations are sequentially programmed in the next preset station group. BASIC OPERATION English 5

28 FM/AM TUNING Customized automatic preset tuning You can specify a preset station group and a preset station number from which this unit stores the FM stations received by automatic preset tuning. Press and hold MEMORY on the front panel for more than 3 seconds. MEMORY MAN'L/AUTO FM 3 Press TUNING l / h on the front panel to begin automatic preset tuning. Press h to tune into higher frequencies. Press l to tune into lower frequencies. When automatic preset tuning is complete, the frequency of the last preset station is shown in the front panel display. l TUNING h Press and then press one of the preset station number buttons on the front panel to select the preset station group and the preset station number where the first received station will be stored. For example, if you select C5, the first received station is automatically programmed to C5 and the next received stations are sequentially programmed to C, C7, etc. Note Automatic preset tuning stops when the received stations have all been stored up to E

29 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP FM/AM TUNING Manual preset tuning You can also manually store up to stations ( stations in each of the 5 groups, A to E). You can then easily recall any preset stations by selecting the preset station numbers where they are stored. Press one of the preset station number buttons on the front panel to select a preset station number ( to ) where you want to store the station Repeat steps to in Automatic tuning or in Manual tuning to tune into a station. When you tune into a station, the frequency of the received station is shown in the front panel display. Press MEMORY on the front panel. The MEMORY indicator flashes in the front panel display for approximately 5 seconds. MEMORY MAN'L/AUTO FM 3 Press on the front panel repeatedly to select a preset station group (A to E). The selected preset station group is shown in the front panel display. MEMORY Flashes Note This operation must be done within 5 seconds while the MEMORY indicator is flashing in the front panel display. Otherwise, the manual preset tuning process is automatically canceled. 5 Press MEMORY on the front panel to store the station. Repeat steps to 5 to store other stations. Notes Any station data stored under a preset station number is cleared when you store a new station under that preset station number. The reception mode (stereo or monaural) is stored along with the station frequency. BASIC OPERATION English 7

30 MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS FM/AM EDIT l TUNING h MEMORY MAN'L/AUTO FM REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R LOUDNESS FLAT 5 7 TUNING MODE AUTO/MAN'L 3dB 3 9 PURE DIRECT -db CD DIRECT AMP MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP FM/AM TUNING Selecting preset stations You can tune into the desired station simply by selecting the preset station number where it is stored. Exchanging preset stations You can exchange the assignment of two preset stations with each other. The following procedure describes an example where a preset station E is exchanged with another preset station A5., Press on the front panel repeatedly (or press j / i on the remote control) to select a preset station group (A to E). The selected preset station group is shown in the front panel display. Front panel or ENTER PRESET/CH Remote control Press one of the preset station number buttons on the front panel (or PRESET/CH u / d on the remote control) to select a preset station number ( to ). The preset station number appears in the front panel display along with the reception band and the frequency Front panel or Repeat steps and in Selecting preset stations to select a preset station E. Press EDIT on the front panel. E and the MEMORY indicator flash in the front panel display. EDIT 3 Repeat steps and in Selecting preset stations to select another preset station A5. A5 and the MEMORY indicator flash in the front panel display. MEMORY Flashes Press EDIT on the front panel again. E-A5 appears in the front panel display, indicating that the two preset station assignments have been exchanged. EDIT MEMORY Flashes ENTER PRESET/CH Remote control

31 . MASTER ON OFF MAIN ZONE ON/OFF A B INPUT ZONE ON/OFF ZONE CONTROL PHONES BASS l TUNING h REC OUT SOURCE MD/TAPE CD TREBLE BALANCE L R FM/AM EDIT MEMORY MAN'L/AUTO FM LOUDNESS FLAT TUNING MODE AUTO/MAN'L 3dB PURE DIRECT -db CD DIRECT AMP ADVANCED SETUP ADVANCED SETUP ADVANCED SETUP menu parameters Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. Factory presets PRESET Use to reset all parameters to the factory presets. Choices: CANCEL, RESET Select CANCEL if you do not want the parameters of this unit to be initialized when you reset the factory presets. Select RESET if you want all of the parameters of this unit to be initialized when you reset the factory presets. Notes This setting does not affect the parameters in the ADVANCED SETUP menu. The resetting process starts next time you turn on the power of this unit. Changing the ADVANCED SETUP menu parameters The ADVANCED SETUP menu is displayed in the front panel display. y During the ADVANCED SETUP procedure, audio output is muted. During the ADVANCED SETUP procedure, only MASTER ON/OFF, and the preset station number buttons ( and ) on the front panel are operational.,,5 Remote REMOTE Use to switch the remote control ID of this unit. Choices: ID, ID Select ID to operate this unit using an alternative code. Select ID to operate this unit using the default code. Note You must also make settings for the remote control (see page 3) and the Zone remote control (see page 9). Tuner TU (Asia and General models only) Use to switch the frequency step selection according to the frequency spacing in your area. Choices: AM/FM, AM9/FM5 North, Central and South America: AM/FM (khz) Other areas: AM9/FM5 (khz), 3 Press MASTER ON/OFF on the front panel to release it outward to the OFF position. Press and hold on the front panel and then press MASTER ON/OFF inward to the ON position. The power of this unit is turned on, and the ADVANCED SETUP menu appears in the front panel display. MASTER ON OFF While holding down, press MASTER ON OFF ADVANCED OPERATION English 9

American Horror Story Season 8 Episode 6 | Les Bracelets Rouges | TRANSSEXUELL SEIN FÜR AUFMERKSAMKEIT